Welcome to
rpsales.net

RC Car Index

Musical Instrument Index

Helicopters

Raptor 30 #1

Raptor 37

Raptor 30-50

F M A Co-Pilot

Tools

Electronics

Raptor 90 SE

Raptor MD-500

Real Flight Simulator


This is a brand new never before flown v1 Raptor 30 Helicopter with the flight box and everything need to assemble fly and repair this machine. I bought this heli new and have had it for almost two years it is fully assembled and ready to go I just could not get the time to go to the field and learn to fly it it has only been ran twice on a stand to make adjustments and break in motor here is a list of all of the goodies that will be sold with it

  • RAPTOR 30 HELICOPTER WITH ALL ELECTRONICS INSTALLED
  • FUTABA 8UHS PCM SUPER COMPUTER RADIO
  • Futaba FP-R148DP ch 47 PCM 1024 Receiver
  • 3 Futaba S9202 Servos Ball Bearing Coreless Aircraft
  • FUTABA 601 GYRO w s9251 Servo (BEST ON MARKET)
  • COPILOT AUTO PILOT SYSTEM
  • G2 FLIGHT SIMULATOR ( FOR COMPUTER PRACTICE)
  • HOBBICO FLIGHT BOX WITH BATTERY FOR STARTER AND PUMP
  • HOBBICO STARTER W/ PLANE AND HELI ADAPTERS
  • HOBBICO HOT SHOT GLO PLUG IGNITER
  • MANUAL FUEL PUMP
  • HELIMAX BLADE PITCH GAUGE
  • BALL LINK PLIERS
  • BALL LINK MEASURING TOOL
  • BALANCER
  • DIGITAL SCALE
  • HOBBICO ALLEN SET
  • SCREW DRIVERS AND MISC. NUT DRIVERS
  • GLO PLUG WRENCH
  • 2 SHIMANO BOXES FULL OF SCREWS BOLTS BEARINGS ZIP TIES SERVO PARTS
  • HELI REPAIR PARTS AND MORE
  • EXTRA BOOM AND FINS
  • ALL MANUELS AND A COPY OF RAYS GUIDE TO HELIS

As you can see this is a pretty extensive list of stuff my loss is your gain I spent about $3,700.00 on everything here this is a very nice heli you will not be dissapointed happy bidding and God Bless You







One Raptor 30 V1 kit, OS 32 Heli engine
plus a upgrade muffler and the origional one as well. One very nice gel coated canopy
and the old origional one as well. One deflector for the muffler.
One Header tank with upgrade bracket. Volt watch to monitor the battery.
Wider landing gear.
Tail mount for the servo with carbon fiber pushrod. Remote glow extension.
One new glow plug #8.
Carbon fiber veritical and horizontal stabilizers with a anodized mounting bracket.
I have some extra parts that will go with the heli, a starter wand, the manual,
blade holder
towerhobbie 7 channel dual conversion reciever on channel 12 with crystal.
I have built a total of 8 machines and I know how to put them together.
Lock tite was use where it is crucial.
Total cost of this package is over $1100.00

  • gy 401 Gyro with 1 Futaba 9253 digital servo for the tail
  • futaba 3305 high torque servo for the collective
  • 3 JR 517 servos





Thunder Tiger Class 30 Raptor Helicopter.
Used, Yes its been crashed and rebuilt a few times. Ready to fly with many extras.
Helicopter upgrades.
Metal Swash Plate,Tail mounted servo,add on Fuel tank,On board Battery indicator
this helicopter comes with every thing needed to fly.
Starter, glow coil ignitor, Volt tester, Hobbico feild box with battery and control panel,
Hobbico quick feild charger, electric fuel pump and manueal fuel pump.
OS engine
A box of spare parts.
Real flight G2 simulater. The radio interface needs to be repaired.
I have the address to send it to. I was told 25.00 will fix it.
I have owned and flown this helicopter for two years.
it is in great shape but needs a new canopy if looks are important to you.
I am moving onto new hobbies and need to fund them.

  • gy 401 Gyro with 1 Futaba 9253 digital servo for the tail
  • JR XP652 Radio & metal storge Case.



Thunder Tiger RAPTOR 50/30 HELICOPTER

  • CONVERTED TO A RAPTOR 50
  • AIRFRAME
  • CANOPY
  • 60 SIZE TAIL ROTOR BLADES
  • NEW 600 WOOD BLADES
  • CARBON FIBER SUPPORT RODS
  • SLIPPER CLUTCH
  • HEAD BUTTON
  • ROTO SPEED 2 OZ. HEADER TANK
  • INLINE FILTER
  • ANDOS 50 SIZE MOTOR MOUNT
  • clutch, fan, clutch bell, 10 tooth pinion on shaft







TT Raptor with 4 HS-425BB, GY-401 and S9253, CF Blades

  • TT36 engine with approximately 5 gallons through it with a muffler
  • 4 Hitec HS425-BB servos
  • Futaba GY401 gyro with S9253 on a tail
  • Aluminum swash plate
  • Aluminum tail control fork
  • Carbon-fiber main blades (Mavrikk)
  • VoltWatch (battery status indicator)






Raptor 30 v2 ready to fly

  • Raptor 30 v2 Chassis Halves,clutch and starter
  • V-1 Pitch arm
  • tt 36 pro
  • Micro pieso giro, servos, glow starter, starter extension shaft
  • futaba t6xa
  • 600ma nicad pack and charger
  • fp-r1270f receiver
  • nes 507 on throttle
  • nes 517 servo on elevator
  • nes 517 servo on aileron
  • Futaba S9202 Servo Ball Bearing Coreless Aircraft pitch
  • Hitec HS-525BB on tail



This is the above heli as offered and purchased by 01152351 from premier-hobby


New Raptor V1 with JR 8103 an lots of parts ready to fly

RAPTOR 30 V1 OS 32 Shark Graphics

Raptor 30




You are bidding on a Raptor 30 49 bb V1 helicopter
JR 8103 helicopter version on CH 33 with digital trims
I`ve had this Heli for 3 years and have approx
3 gallons of 30% CoolPower fuel, maybe a little more
Engine runs great, and makes great power with the Pipe

  • Installed in Heli is:
  • OS 32 SX-H
  • Youngblood MP2 Pipe
  • CSM 400 Heading Lock Gyro
  • Header tank
  • Remote Glow Plug
  • Carbon Fiber Fins
  • Carbon Fiber Tail Mount Rotor Servo
  • Hitec 925 MG Ultra Speed Tail Rotor Servo
  • 4- 537 JR servos
  • JR NER 549 X 9 CH FM Receiver
  • Low Profile Skids
  • Short antenna mounted on Skids
  • Also included in this package is:
  • 1- JR Battery Checker
  • 1- Mavrikk Pitch Gauge (new)
  • 1-Ballink Pliers
  • 1-KSJ Paddle Guage (new)
  • 1-KSJ Blade Balancer (new)
  • 1- DSC Cord FM (new)
  • 1- Gear for Constant Drive Tailrotor (new)
  • 1- Tailboom (new)
  • 1-Washout Set PV0011 (new)
  • 1- package body clips PV0067 (new)
  • 1-Starter Coupling PV0026 (new)
  • 2-Main Shafts AK 0029 (new)
  • 1-Seesaw Stabilizer AK0004 (new)
  • 1- Flybar PV0008 (new)
  • 2- Sets of Tail fins (used)
  • 1- Fan (used)
  • 1-Engine Mount (used)
  • 1- Clutch (used)
  • 1-Clutch Liner (new)
  • 2- Sets of Flybar Paddles (used)
  • 2-Sets Tailrotor Blades (used)
  • 1-Hex Starter Wand
  • 1-Flight Stand (awesome at the field, see pictures)
  • 1-CSM 180 Piezo Gyro (used) Replaced with CSM 400
  • Lots of screws and little parts


Raptor 30

USED RAPTOR 30 V1 HELICOPTER
COMES WITH OS 32, TUNED PIPE
NEW THUNDER TIGER BLADES

Feb-19-05delta2003ss266.55+15.00

Raptor 30

  • RAPTOR 30 V1 HELICOPTER
  • tt36 Engine
  • Servos: JR 537 (5)
  • Ch 24 JR XP652 Transmitter (and Reciever).
  • Telebee Gyro Sensor
  • New receiver battery.
  • Fiberglass main rotors.
  • Volt watch system.
  • Extra tail boom, flybar
  • training gear

7-5-05fusion4646 315+10

Raptor 30 V1


  • 39TT Engine
  • 49 ball bearings
  • TUNED PIPE
  • Wood Blades
  • Carbon Fiber Tail Rotor Blades
  • Purple Metal Pitch Arm
  • Tail Servo Mount
  • Header Tank
  • New Fuel Tank
  • GSM -ICG 400 Heading lock Gyro


7-19-05-225.55+free flymetonight

Thunder Tiger Raptor 30 V1 helicopter


  • OS 32 engine
  • TUNED PIPE
  • Futaba 401
  • S9253 servo for tail
  • 3 jr NEH-531
  • carbon blades
  • Header Tank
  • one way starter shaft
  • cordless starter motor


7-23-05-281.05+24.95refund41.25 cracked frame minhtuanguyen

Thunder Tiger Raptor 30 V1 helicopter


  • OS 32 engine
  • tuned exhaust
  • header tank
  • remote glow starter
  • carbon fiber tail boom stiffners
  • awesome custom paint job.
  • Dynamite Green Fuel Tubing
  • 2 Sets of Tail Fins
  • KS 2oz Header Tank
  • Tail Control Rod Set
  • Hobbico Exhaust Defector
  • Tail Rotor Shaft
  • JR Hex Starter Shaft
  • Remote Safety Ignitor
  • Extra Fuel Tank
  • Revolution Upgrade Servo Mount for Tail
  • 2 pks. of T Fuel Fittings
  • Tail Rotor Hub, Mixing Levers
  • Tail Rotor Grips
  • Lots of Colorful Fuel Tubbing.
  • Stock Tail Boom Stiffners
  • Manual Fuel Pump
  • flown about 15-20 times


7-23-05-266.66+27 2nd bidfalcon41176

Thunder Tiger Raptor 30 V1 helicopter


  • OS 32 engine as new
  • Pipe
  • bent boom
  • broken tail
  • Broken head parts
  • Broken Stabilizer Fin
  • Bent Boom Supports
  • Bent tail rotor control wire
  • stripped one way screws (2)
  • broken landing gear
  • cracked frame
  • rx 36 r600 cut antenna
  • 4 x nes-507 servos
  • ICG 180 Gyro
  • No TX



8-28-05-202.50+18 bikeparts01